1. FEATURES AND SPECIFICATIONS

The TypeⅠIntelligent Battery Guard continually monitors the battery charge ,and automatically disconnects the battery from the electricity system if it detects that the power is falling below the level that is required to start the engine.

The TypeⅠIntelligent Battery Guard does not have remote controls, in case the Intelligent Battery Guard  disconnects the power when detects an electricity leakage, press and release the blue manual reset knob on the top of the unit to reconnect the power.

2. INSTALLATION

Package Contents

One open-end 17mm and one adjustable wrench, standard and Phillips screwdrivers.

Installation Steps

Step 1: Turn the ON/OFF Blue knob on the top of the unit to one of the “ON” position

A)  Disconnect the black negative cable from the negative post on the battery.
B)  Disconnect the red positive cable from the positive post on the battery.

Step 3: Connecting the Intelligent Battery Guard

A:  Connect the Positive Clamp set on the positive side of the Intelligent Battery Guard, the positive
      side of the Intelligent Battery Guard is located on the side of the unit that has 12V+ printed on it.
B:  Connect the Aluminum Positive Post set on the other side of the Intelligent Battery Guard.
C:  Connect the positive clamp onto the battery.

Note: The positive cable must not come into contact with the ACC clip.

Now let's find an appropriate configuration option for the Intelligent Battery Guard. Battery location and position differ depending on the vehicle, the Intelligent Battery Guard can be configured for various top mounting, side mounting, and chassis installations (see below).

A:  Connect the red/positive battery cable to the aluminum post on the outer bracket of the
      Intelligent Battery Guard.
B:  Connect the black negative battery cable to the negative post on the battery .
C:  Connect the clip end of the black ground wire to the clamp bolt on the negative post on the
      battery.

Step 4: Accessory Bypass Wire Installation

A.  Slide the connecter end of the Bypass wire onto the Butterfly Connector on the female positive
     post of Intelligent Battery Guard.
B.  Locate the motor's fuse box and the desired fuse.
C.  Remove the fuse and insert it into the fuse connection in the bypass wire.
D.  Connect the exposed end of the bypass wire into the outbound leg of the fuse box to activate the
      device.

Step 5: Disabling connection/motor on wire installation 

A.  Locate a fuse in the fuse box that has current when the motor is turned on and no current when
      the motor is turned off. This wire can be connected directly to the key switch.
B.  Remove fuse .
C.  Connect the exposed end of the bypass wire into the fuse box.
D.  Slide the connector end of the bypass wire onto the single connector on the negative side of the
      Intelligent Battery Guard. The connector is marked “ACC”.

3. TEST INSTALLATION RESULT

To test successful installation
Start the vehicle after installation is completed.

To test Intelligent Battery Guard operation
Turn the vehicle off and turn on as many electrical accessories (i.e. lights, radio,) as possible and leave them on. The intelligent Battery Guard will cut power form the battery automatically confirming it is working. This may take some time, depending on the battery's age and charge.

To test manual reset function
Ensure that the blue Manual reset knob is in one of the “ON” position and press it down after the Intelligent Battery Guard had disconnected the power, the unit should re-establish power to the electrical accessories and enable you to start the vehicle.

4. IMPORTANT NOTICE

If a warning light for NO CHARGE or BATTERY WARNING illuminates on your vehicle dashboard, stop your vehicle at a safe area and turn the blue knob to one of “OFF” positions, your vehicle will experience a complete loss of power unless the“NO CHARGE”problem is repaired immediately!  This problem is unrelated to the intelligent Battery Guard and requires assistance from an Auto Technician.

If the unit detects the battery voltage is less that 12V, it will completely disconnect the power, and the settings will be lost. If it happens, Press and release the blue button on the top of the unit and wait 30 seconds in order to allow the computer to reset itself before start the engine. In case you need to keep one or two accessories always energized, connect the accessory directly to the positive post of the battery.